SANDBOX — this is a test environment. No servers are actually deployed and no real payments are charged.
Source-checkedTechnology & automation

Pipe Meter (Updated)

by Walkman100 · for Factorio

Read fluid levels in a pipe with the circuit network without use of a bulky tank. Updated to 1.1.x by Walkman100

1.7KDownloads
5 yr agoLast updated
MITLicense
1.1Latest game version

About Pipe Meter (Updated)

From Factorio Mod Portal

Read fluid levels in a pipe with the circuit network without use of a bulky tank. Updated to 1.1.x by Walkman100

NOTE: This is PipeMeter updated for 1.1.x

Original Mod Description:

NOTE: This is mostly a proof-of-concept and to see if the idea had any value to the community. At this point, the idea has been shared and integrated/refined for later factorio versions.

Simple 1-tile entity that allows for connection of pipes to the circuit network. Should behave like any other pipe section, connecting on all four sides.

Level Meter:

This is for those that want to monitor fluid levels, but do not want to use a huge tank.

Range is read from 0-100 (99.9 actually). No more calculations, and think in percentages instead of total units.

Flow Meter Arrangement:

Because pipes offer a bit of resistance, adjacent pipe sections show varied levels depending on flow. Two meters can be inserted in-line to pipe flow, and their levels checked against one another to determine flow (see screenshot).

My rough test have seen about a 3% flow restriction when using this setup (That is to say that filling a tank straight from an off-shore pump takes only a few seconds more with the meters than with straight pipe). Max delta I as able to achieve was 10 (likely keyed to pipe 'diameter', and thus larger/smaller pipes will show larger/smaller max delta)

Notes:

This is actually a small, 100 capacity tank, and thus has a slight internal reserve. It responds well to level changes, but reacts slightly slower than the surrounding pipe sections to fluid level. It should flow the same as vanilla pipe. It can be used in place of a pipe section, or off to the side as shown in the thumbnail.

Highlights

From source data

Game versions

Built for Factorio 1.1.

Footprint

Rated a light load on a server.

License

Published under MIT.

Pipe Meter (Updated) on Nxeon

From our catalogue
One-click install
Supported on Nxeon Factorio servers. We download it from Factorio Mod Portal, place it, and restart the server.
Server side
Required on the server
Server load
light
Smallest plan we suggest
Factorio — 2 GB (2 GB RAM). This follows our own load rating above, not a benchmark.
Latest build
0.0.3, released 2021-10-30

Run Pipe Meter (Updated) on a Factorio server

Pick a server or deploy a new one above; it is installed in one click.

What kind of mod it is

From the catalog
Listed on Factorio Mod Portal as “Mods”

Technology & automation

Machines, power, logistics and automation.

Runs on your server

From source side support

Factorio Mod Portal lists Pipe Meter (Updated) as required on the server. Check its Factorio Mod Portal page to see whether players need it too.

Compatibility

Game
Factorio
Runs on
Serverrequired on the server
Game versions
1.1

Verified at the source

  • ✓Factorio Mod PortalOfficial listing, checked 2026-10-08Open ↗
  • ✓AuthorWalkman100, as published on Factorio Mod Portal
  • ✓LicenseMITFree

Pipe Meter (Updated), answered

Generated from the mod’s own source data.

Do my players need to install Pipe Meter (Updated)?

Factorio Mod Portal lists Pipe Meter (Updated) as required on the server. Check its Factorio Mod Portal page to see whether players need it too.

Is it free?

Yes. Pipe Meter (Updated) is free to download from Factorio Mod Portal. Its license is MIT.

How do I add it to my Nxeon server?

Use “Add to a server” on this page, or open NxLabs from your dashboard. We install it, restart your server and switch it on.

NxLabs

Run Pipe Meter (Updated) on a Factorio server.

Deploy in about a minute from $2.99 a month, then add Pipe Meter (Updated) in one click.